哈飛微型面包車整體式驅動橋設計【含5張CAD圖紙和說明書】

哈飛微型面包車整體式驅動橋設計【含5張CAD圖紙和說明書】,含5張CAD圖紙和說明書,微型,面包車,整體,總體,驅動,設計,cad,圖紙,以及,說明書,仿單 哈飛微型面包車整體式驅動橋設計 摘 要 本次設計的題目是哈飛民意汽車驅動橋設計。驅動橋一般由主減速器、差速器、半軸及橋殼四部分組成，其基本功用是增大由傳動軸或直接由變速器傳來的轉矩，將轉矩分配給左、右車輪，并使左、右驅動車輪具有汽車行駛運動學所要求的差速功能；此外，還要承受作用于路面和車架或車廂之間的鉛垂力、縱向力和橫向力。 本設計首先論述了驅動橋的總體結構，在分析驅動橋各部分結構型式、發展過程及其以往形式的優缺點的基礎上，確定了總體設計方案：采用整體式驅動橋，主減速器的減速型式采用單級減速器，主減速器齒輪采用螺旋錐齒輪，差速器采用普通對稱式圓錐行星齒輪差速器，半軸采用半浮式型式，橋殼采用鋼板沖壓焊接式整體式橋殼。 關鍵詞： 驅動橋；主減速器；設計；計算；CAD 8 ABSTRACT The object of the design is the design for driving axle of mini-car of SongHuajiang driving axle is consisted of final drive, differential mechanism, half shaft and axle housing. The basic function of driving axle is to increase the torque transmitted by drive shaft or directly transmitted by gearbox, then distributes it to left and right wheel, and make these two wheels have the differential function which is required in automobile driving kinematics; besides, the driving axle must also stand the lead hangs down strength, the longitudinal force and the transverse force acted on the road surface, the frame or the compartment lead. The configuration of the driving axle is introduced in the thesis at first. On the basis of the analysis of the structure ,the developing process and advantages and disadvantages of the former type of driving axle, the design adopted the Integral driving axle, single reduction gear for main decelerator’s deceleration form, spiral bevel gear for main decelerator’s gear, half floating for axle and stamp-welded steel sheet of integral axle housing for axle housing. In the design, we accomplished the design for single reduction gear, tapered planetary gear differential mechanism, half floating axle, the checking of axle housing and CAD drawing and so on. . Keywords: Driving Axle; Final Drive ; Design; Calculation; CAD 目 錄 第1章 緒 論 1 1.1 驅動橋的結構和種類 1 1.1.1 汽車車橋的種類 1 1.1.2 驅動橋的種類 1 1.1.3 驅動橋結構組成 2 1.2設計內容 6 第2章 設計方案的確定 7 2.1 設計主要參數 7 2.2主減速器結構方案的確定 7 （1）主減速器齒輪的類型的選擇 7 2.3差速器結構方案的確定 8 2.4 半軸型式的確定 8 2.5 橋殼型式的確定 9 2.6 本章小結 9 第3章 主減速器設計 10 3.1 主減速比的確定 10 3.2 主減速器齒輪計算載荷的確定 10 3.3 主減速器齒輪參數的選擇 11 3.4 主減速器螺旋錐齒輪的幾何尺寸計算與強度計算 12 3.4.1 主減速器螺旋錐齒輪的幾何尺寸計算 12 3.4.2 主減速器螺旋錐齒輪的強度計算 13 3.5 主減速器齒輪的材料及熱處理 16 3.6 主減速器軸承的計算 17 3.7 主減速器的潤滑 21 3.8 本章小結 21 第4章 差速器設計 22 4.1 概述 22 4.2 對稱式圓錐行星齒輪差速器 22 4.2.1 差速器齒輪的基本參數選擇 23 4.2.2 差速器齒輪的幾何尺寸計算與強度計算 24 4.3 本章小結 27 第5章 半軸設計 28 5.1 概述 28 5.2 半軸的設計與計算 28 5.2.1半浮式半軸的設計計算 28 5.2.2 半軸的結構設計 31 5.3 本章小結 32 第6章 驅動橋橋殼的校核 33 6.1 概述 33 6.2 橋殼的受力分析及強度計算 33 6.2.1 汽車以最大牽引力行駛時的橋殼強度計算 33 6.2.2 汽車側向力最大時的橋殼強度計算 33 6.2.3 汽車在不平路面沖擊載荷作用下橋殼的強度計算 34 6.3 本章小結 34 參考文獻 37 致 謝 38 附 錄A 外文文獻 39 附 錄B外文文獻的中文翻譯 42