喜歡這套資料就充值下載吧。。。資源目錄里展示的都可在線預覽哦。。。下載后都有，，請放心下載，，文件全都包含在內，，【有疑問咨詢QQ:1064457796 或 1304139763】
黑龍江工程學院本科生畢業設計
目 錄
摘要.........................................................................................................................Ⅰ
Abstract....................................................................................................................Ⅱ
第1章 緒論.........................................................................................................1
1.1 引言..........................................................................................................1
1.2 離合器研究現狀......................................................................................3
1.2.1 國外研究現狀...................................................................................3
1.2.2 國內研究現狀...................................................................................4
1.3 本設計的目的和意義................................................................................5
1.4 本設計的主要內容....................................................................................5
第2章 膜片彈簧離合器基本參數的選擇..............................................5
2.1 離合器的原理及應滿足的要求................................................................5
2.2 壓緊彈簧的結構型式及............................................................................6
2.2.1 周置彈簧離合器...............................................................................6
2.2.2 中央彈簧離合器...............................................................................7
2.2.3 斜置彈簧離合器...............................................................................7
2.2.4 膜片彈簧離合器...............................................................................7
2.3 基本結構尺寸參數的選擇......................................................................8
2.3.1 摩擦片的設計...................................................................................8
2.3.2 后備系數β的確定...........................................................................8
2.3.3單位壓力P0的確定...........................................................................9
2.3.4摩擦因子f選擇.................................................................................9
2.4 摩擦片的優化............................................................................................9
2.5 本章小結..........................................................................................10
第3章 從動盤總成設計................................................................................11
3.1 從動盤的組成型式及要求........................................................................11
3.2 從動片設計................................................................................................11
3.3 從動盤轂的設計.......................................................................................11
3.4 花鍵強度校核...........................................................................................12
3.5 從動盤摩擦材料選擇...............................................................................12
3.6 扭轉減震器的設計...................................................................................13
3.6.1 扭轉減震器的功能........................................................................13
3.6.2 扭轉減震器主要參數的選擇 .......................................................13
3.6.3 減震彈簧的計算............................................................................15
3.7 本章小結...................................................................................................16
第4章 膜片彈簧、壓盤和離合器蓋的設計...........................................17
4.1 膜片彈簧基本參數的選擇.......................................................................17
4.1.1 H/h 比值的選擇...............................................................................17
4.1.2 碟簧部分大端半徑R、內半徑r及R/r 的比值確定.................17
4.1.3 彈簧起始圓錐底角的選擇........................................................17
4.1.4 膜片彈簧小端半徑r0 及分離軸承作用半徑rf選擇 ...................17
4.1.5 分離指數目n 切槽寬度窗口槽寬及半徑re選擇.................17
4.1.6壓盤加載點R1和支撐環加載點半徑r1選取..................................18
4.2 膜片彈簧的設計........................................................................................18
4.2.1繪制特性曲線.......................................................................18
4.3膜片彈簧工作點位置的選擇.....................................................................20
4.4 求離合器徹底分離時分離軸承作用的載荷F2.的計算..................................21
4.5 分離軸承的行程的計算........................................................................21
4.6 膜片彈簧的強度校核.................................................................................22
4.7 膜片彈簧的優化.........................................................................................23
4.8 壓盤傳動方案的選擇.................................................................................24
4.9 壓盤的材料選擇.........................................................................................24
4.10 壓盤幾何尺寸的確定...............................................................................24
4.11 離合器蓋的設計.......................................................................................25
4.12 本章小結...................................................................................................26
第5章 離合器操縱機構的設計.......................................................................27
5.1 離合器操縱機構的要求.............................................................................27
5.2 操縱機構的設計.........................................................................................27
5.2.1 操縱機構的組成及優點....................................................................27
5.2.2 踏板行程S的計算............................................................................27
5.3 踏板力的計算........................................................................................28
5.4 助力器缸直徑計算.....................................................................................28
5.5 分離軸承的選擇和校核.............................................................................29
5.6 本章小結.....................................................................................................29
結論...........................................................................................................................30
參考文獻..................................................................................................................31
致謝.............................................................................................................................32
附錄A..........................................................................................................................33
附錄B..........................................................................................................................34