甲醇精餾塔設計（全套CAD圖+說明書+開題報告+翻譯）

甲醇精餾塔設計（全套CAD圖+說明書+開題報告+翻譯）,甲醇,精餾塔,設計,全套,cad,說明書,仿單,開題,報告,講演,呈文,翻譯 甲醇精餾塔設計 摘要：填料塔為連續接觸的氣液傳質設備，與板式塔相比，不僅結構簡單，而且具有生產能力大，分離填料材質的選擇，可處理腐蝕性的材料，尤其對于壓強降較低的真空精餾操作，填料塔更顯示出優越性。本文以甲醇-水的混合液為研究對象，因甲醇-水系統在常壓下相對揮發度相差較大，較易分離，所以設計采用常壓精餾。根據物料性質，操作條件等因素選擇填料塔，此設計采用高位泡點進料、塔底再沸器和塔頂冷凝器的重力回流方式，將甲醇-水進行分離的填料精餾塔。本設計中已知了塔徑和塔高，可根據經驗公式計算填料層高度，而且可根據塔徑可以對填料支撐，液體分布，裙座等塔的構建進行選型。根據已知的條件結合書上的計算公式和參數，對塔設備進行強度的設計，設計塔設備的尺寸，并對設計的塔設備數據進行穩定校核，以確保設計能滿足各項標準，從而得到分離甲醇-水混合物液的填料精餾塔。 關鍵字：填料塔；優越性；常壓精餾；塔構建選型；強度設計；穩定校核 Methyl alcohol rectifying tower design Abstract: The Packed tower is continuous contact with the gas-liquid mass transfer equipment, compared with tray column, The Packed tower not only has a simple structure, but also has higher capacity to product, The Packed tower can choose the separation of packing materials and handle corrosive materials, especially for operation of low pressure drop vacuum distillation, and the packed column shows superiority. In this paper, methanol–water mixture as the object of study. Because methanol - water system has a wide relative volatility at atmospheric, so the design adopt atmospheric pressure distillation. According to the material properties, operating conditions and other factors, we select packed tower. This design uses a high bubble point feed, bottom and top of the tower reboiller gravity reflux condenser, methanol - water distillation column packing to separate. The design of known diameter and tower height of the tower can be calculated based on experience packing layer height and diameter can be packed under the support tower, liquid distribution, the construction of the skirt so the selection of the tower. According to the book with known conditions and parameters of the formula, the strength of the tower equipment design, the size of tower equipment design, and design of the tower equipment calibration and stability data to ensure that the design can meet the standards, the get packed distillation column of separating methanol and water. Keywords: packed tower; superiority; atmospheric distillation; tower building selection; strength design; stability check. 目 錄 引言…………………………………………………………………1 1 已知設計參數…………………………………………………… 4 2 設計方案的確定………………………………………………… 4 3 塔設備的選型…………………………………………………… 4 3.1 塔型………………………………………………………… 4 3.2 填料的選擇……………………………………………… 4 3.3 填料層的高度計算及分段………………………………… 5 4 填料塔內件的結構設計……………………………………… 5 4.1 填料支承裝置………………………………………………… 5 4.2 填料的壓緊及限位裝置……………………………………… 6 4.3 填料塔液體分布器…………………………………………… 7 4.4 液體收集再分布器…………………………………………… 8 5 塔設備的附件…………………………………………………… 9 5.1 除沫器………………………………………………………… 9 5.2 裙座…………………………………………………………… 9 5.3 地腳螺栓座…………………………………………………… 10 5.4 排氣管和排氣孔……………………………………………… 11 5.5 塔底接管引出孔……………………………………………… 11 5.6 檢查孔………………………………………………………… 12 5.7 塔內和裙座內爬梯…………………………………………… 12 5.8 地腳螺栓……………………………………………………… 12 5.9 地腳螺栓模板………………………………………………… 13 5.10 塔頂?shù)踔?………………………………………………………13 5.11 塔釡隔板……………………………………………………… 13 5.12 接管…………………………………………………………… 13 5.13 管口擋板……………………………………………………… 14 5.14 人孔和手孔 ……………………………………………………14 5.15 塔的保溫支撐件 ………………………………………………14 5.16 操作平臺和梯子 ………………………………………………14 6 設備的強度設計和穩定校核 ……………………………………15 6.1 筒體和封頭尺寸計算……………………………………………15 6.2 載荷分析 ……………………………………………………… 17 6.3 自振周期計算 ………………………………………………… 20 6.4 風載荷和風彎矩計算 ………………………………………… 21 6.5 地震載荷和地震彎矩計算 …………………………………… 24 6.6 偏心載荷與偏心彎矩計算 …………………………………… 26 6.7 最大彎矩 ……………………………………………………… 26 6.8 強度校核 ……………………………………………………… 26 參考文獻 ……………………………………………………………… 36 附錄 英文原文……………………………………………………………………38 譯文…………………………………………………………………………52 謝辭 ………………………………………………………………………62 iv